View C0805X7R160-XXXX_88581.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

www..com
Ceramic Chip Capacitors
Multilayer chip capacitors have a low residual inductance, an excellent frequency response and minimal stray capacitance since there are no leads. These characteristics enable design to be very close to the theoretical values of the capacitors.
NP0/C0G:
15% 10% 5% 0% -5% -10% -15% -55C -25C 0C
SPECIFICATIONS:
Typical Capacitance Change vs. Temperature
OPERATING TEMPERATURE RANGE: TEMPERATURE COEFFICIENT: TEMPERATURE VOLTAGE COEFFICIENT: DISSIPATION FACTOR: INSULATION RESISTANCE: AGEING: WITHSTANDING VOLTAGE: TEST PARAMETERS:
25C
50C
75C
100C
125C
CAPACITANCE TOLERANCE: OPERATING TEMPERATURE RANGE: TEMPERATURE COEFFICIENT: TEMPERATURE VOLTAGE COEFFICIENT: DISSIPATION FACTOR:
-55C to +125C 0 30PPM/C 0 30PPM/C 0.1% MAX. >1000 ohms F or 100 G ohms, whichever is less at 25C, VDCW. (The IR at 125C is 10% of the value at 25C) None >2.5 times VDCW 1MHz 100KHz at 1.0 0.2 Vrms 100 pF, 25C 1KHz 100Hz at 1.0 0.2 Vrms > 100 pF, 25C B,C,D,F,G,J,K -55C to +125C 0 15%C MAX. X7R not applicable For 50 volts and 100 volts: 2.5% MAX.; For 25 volts: 3.0% MAX.; For 16 volts: 3.5% MAX.; For 10 volts: 5.0% MAX.; For 6.3 volts: 10% MAX. For values > 10F and voltages 10V, the D.F. is 10% MAX. >1000 ohms F or 100 G ohms, whichever is less at 25C, VDCW. (The IR at 125C is 10% of the value at 25C) 2.5% per decade hour, typical >2.5 times VDCW 1KHz 100Hz at 1.0 0.2 Vrms > 100 pF, 25C J,K,M -55C to +85C 0 15%C MAX. X5R not applicable For 50 volts and 100 volts: 2.5% MAX.; For 25 volts: 3.0% MAX.; For 16 volts: 3.5% MAX.; For 10 volts: 5.0% MAX.; For 6.3 volts: 10% MAX. For values > 10F and voltages 10V, the D.F. is 10% MAX. >1000 ohms F or 100 G ohms, whichever is less at 25C, VDCW. (10,000 ohms at 125C) 2.5% per decade hour, typical >2.5 times VDCW 1KHZ 100Hz at 1.0 0.2 Vrms > 100 pF, 25C J,K,M +10C to +85C +22% - 56%C MAX. 4.0% MAX. >100 ohms F or 10 G ohms, whichever is less at 25C, VDCW. 5% per decade hour, typical >2.5 times VDCW 1KHz 100Hz at 0.5 0.1 Vrms, 25C M,Z,P
X7R:
15% 10% 5% 0% -5% -10% -15% -55C -25C 0C
SPECIFICATIONS:
Typical Capacitance Change vs. Temperature
INSULATION RESISTANCE: AGEING: WITHSTANDING VOLTAGE: TEST PARAMETERS:* CAPACITANCE TOLERANCE: OPERATING TEMPERATURE RANGE: TEMPERATURE COEFFICIENT: TEMPERATURE VOLTAGE COEFFICIENT: DISSIPATION FACTOR:
25C
50C
75C
100C
125C
X5R:
15% 10% 5% 0% -5% -10% -15% -55C -25C 0C
SPECIFICATIONS:
Typical Capacitance Change vs. Temperature
INSULATION RESISTANCE: AGEING: WITHSTANDING VOLTAGE: TEST PARAMETERS:* CAPACITANCE TOLERANCE: OPERATING TEMPERATURE RANGE: TEMPERATURE COEFFICIENT: DISSIPATION FACTOR: INSULATION RESISTANCE: AGEING: WITHSTANDING VOLTAGE: TEST PARAMETERS: CAPACITANCE TOLERANCE:
25C
50C
75C
100C
125C
Z5U:
20% 0% -20% -40% -60% -80%
SPECIFICATIONS:
Typical Capacitance Change vs. Temperature
-55C
-25C
0C
25C
50C
75C
100C
125C
Y5V:
40% 20% 0% -20% -40% -60% -80% -100% -55C -25C 0C
SPECIFICATIONS:
Typical Capacitance Change vs. Temperature
OPERATING TEMPERATURE RANGE: TEMPERATURE COEFFICIENT: DISSIPATION FACTOR:
25C
50C
75C
100C
125C
INSULATION RESISTANCE: AGEING: WITHSTANDING VOLTAGE: TEST PARAMETERS:* CAPACITANCE TOLERANCE:
-30C to +85C +22% - 82%C MAX. For 25 volts and 50 volts: 5% MAX.; For 16 volts: 7% MAX.; For 10 volts: 9% MAX.; For 6.3 volts: 11% MAX. For higher Cap values > 10F, the D.F. is 20% MAX. >100 ohms F or 10 G ohms, whichever is less at 25C, VDCW. 7% per decade hour, typical >2.5 times VDCW 1KHz 100Hz at 1.0 0.2 Vrms, 25C M,Z
*
6
Test parameters for Hi-Caps: X7R, X5R and Y5V 1KHz 100Hz at 1.0 0.2 Vrms 10uF (10 V min.) 1KHz 100Hz at 0.5 0.1 Vrms 10uF (6.3V max.) 120Hz 24Hz at 0.5 0.1 Vrms > 10uF
All components in this section are RoHS compliant per the EU directives and definitions.
All tape and reel www..com specifications must be adhered to per EIA-481-1-A as noted and stated in the Chip Resistor section on page 65.
G
Reel Dimensions
TAPE B min C A (7") A (13") D min N min G
Unit: mm (inch)
T max
B A D
FULL RADIUS
8mm
N C
12mm
0.3 (.012) 0.3 (.012)
13 .05 (.512 .02) 13 .05 (.512 .02)
178 2.0 (7 .079) 178 2.0 (7 .079)
330 2.0 (13 .08) 330 2.0 (13 .08)
20.2 (.795) 20.2 (.795)
50 (1.97) 50 (1.97)
10 1.5 (.394 .059) 10 1.5 (.394 .059)
14.9 (.587) 14.9 (.587)
Taping Specifications
To T D
10 PITCHES CUMULATIVE TOLERANCE 0.008 ( 0.2 )
7 in. Reel Quantities**
SIZE
T
01005
0201*
0402*
0603
0805
1206
1210
1812
2221
TAPE SIZE
Po Pz E
8mm 20,000 20,000
8mm 15,000 15,000
8mm 5000 10,000
8mm 3000 4000
8mm 3000 5000
8mm 2000 5000
8mm 1000 5000
12mm 1000 3000
12mm 1000 1000
MIN QTY PER REEL MAX QTY PER REEL
A B
F
W
t EMBOSSED PAPER
TOP TAPE DIRECTION OF FEED
P
CENTER OF CAVITY
** Quantity dependent on Chip Thickness * 0201 and 0402 Pitch ("P") is .079" .004" (2.0 0.1mm) Smaller quantities may be available. Please contact your sales person. Unit: mm (inch)
Paper Tape Carrier Dimensions (8mm)
SIZE 01005
A 0.25 0.05 (0.010 .002) 0.37 0.05
B 0.45 0.05 (0.018 .002) 0.67 0.05 (0.026 .002) 1.10 0.2 (.043 .008) 1.90 0.2 (.075 .008) 2.4 0.2 (.095 .008) 3.6 0.2 (.142 .008) B
W 8.0 0.2 (.315 .008) 8.0 0.2 (.315 .008) 8.0 0.2 (.315 .008) 8.0 0.2 (.315 .008) 8.0 0.2 (.315 .008) 8.0 0.2 (.315 .008) W
F 3.5 0.1 (.138 .004) 3.5 0.1 (.138 .004) 3.5 0.1 (.138 .004) 3.5 0.1 (.138 .004) 3.5 0.1 (.138 .004) 3.5 0.1 (.138 .004) F
E 1.75 0.1 (.069 .004) 1.75 0.1 (.069 .004) 1.75 0.1 (.069 .004) 1.75 0.1 (.069 .004) 1.75 0.1 (.069 .004) 1.75 0.1 (.069 .004) E
Po 4.0 0.1 (.157 .004) 4.0 0.1 (.157 .004) 4.0 0.1 (.157 .004) 4.0 0.1 (.157 .004) 4.0 0.1 (.157 .004) 4.0 0.1 (.157 .004) Po
Pz 2.0 0.05 (.039 .002) 2.0 0.05 (.039 .002) 2.0 0.05 (.039 .002) 2.0 0.05 (.079 .002) 2.0 0.05 (.079 .002) 2.0 0.05 (.079 .002) Pz D
( ( ( ( ( (
0201 (0.014 .002) 0.65 0.1 0402 (.026 .004) 1.10 0.2 0603 (.043 .008) 1.16 0.2 0805 (.046 .008) 2.0 0.2 1206 (.079 .008)
D 1.5 + 0.1 - 0.0 .064 + .004 - .000 1.5 + 0.1 - 0.0 .064 + .004 - .000 1.5 + 0.1 - 0.0 .064 + .004 - .000 1.5 + 0.1 - 0.0 .064 + .004 - .000 1.5 + 0.1 - 0.0 .064 + .004 - .000 1.5 + 0.1 - 0.0 .064 + .004 - .000
t 1.15 MAX
P 2.0 0.05 (.079 .002) 2.0 0.05 (.079 .002) 2.0 0.05 (.079 .002) 4.0 0.1 (.157 .004) 4.0 0.1 (.157 .004) 4.0 0.1 (.157 .004) P
) ) ) ) ) )
(.045 MAX) 1.15 MAX (.045 MAX) 1.15 MAX (.045 MAX) 1.15 MAX (.045 MAX) 1.15 MAX (.045 MAX) 1.15 MAX (.045 MAX) T
Embossed Carrier Dimensions (8mm & 12mm)
SIZE
A
To
1.48 0.2 0805
2.3 0.2
8.0 0.2
3.5 .0.1
1.75 0.1
4.0 0.1
2.0 0.05
(.058 .008) (.091 .008) (.315 .008) (.138 .004) (.069 .004) (.157 .004) (.079 .002) 2.0 0.2 1206 (.079 .008) (.142 .008) (.315 .008) (.138 .004) (.069 .004) (.157 .004) (.079 .002) 2.9 0.2 1210 3.6 0.2 8.0 0.2 3.5 .0.1 1.75 0.1 4.0 0.1 2.0 0.05 3.6 0.2 8.0 0.2 3.5 .0.1 1.75 0.1 4.0 0.1 2.0 0.05
(.114 .008) (.142 .008) (.315 .008) (.138 .004) (.069 .004) (.157 .004) (.079 .002) 3.6 0.2 4.9 0.2 12.0 0.3 5.6 .0.1 1.75 0.1 4.0 0.1 2.0 0.05
1812 (.142 .008) (.193 .008) (.472 .012) (.221 .004) (.069 .004) (.157 .004) (.079 .002)
1.5 + 0.1 - 0.0 .004 (.06 + .000) 1.5 + 0.1 - 0.0 .004 (.06 + .000) 1.5 + 0.1 - 0.0 .004 (.06 + .000) 1.5 + 0.1 - 0.0 .004 (.06 + .000) -
2.5 MAX
0.6 MAX
4.0 0.1
(.098 MAX) (.024 MAX) (.157 .004) 2.5 MAX 0.6 MAX 4.0 0.1
(.098 MAX) (.024 MAX) (.157 .004) 2.5 MAX 0.6 MAX 4.0 0.1
(.098 MAX) (.024 MAX) (.157 .004) 3.8 MAX 0.6 MAX 8.0 0.1
(.150 MAX) (.024 MAX) (.315 .004)
How To Order
C0805 C0G
Series See Chart
500
--
101
Capacitance (pico - Farads) 1st two digits are significant, followed by number of zeroes. 101 = 100 pF R denotes decimal 6R8 = 6.8 pF
J
Tolerance Code: *B = 0.1 pF *C = 0.25 pF *D = 0.5 pF F = 1% G = 2% J = 5% K = 10% M = 20% N = 30% Z = +80 -20% P = +100 -0% * For capacitance values below 10 pF
N
Temperature Rated Voltage Characteristic 1st two digits are significant followed by number of zeroes. 6R3 = 6.3 VDCW 100 = 10 VDCW 160 = 16 VDCW 250 = 25 VDCW 500 = 50 VDCW 101 = 100 VDCW 201 = 200 VDCW 251 = 250 VDCW
Termination Marking** Packaging Optional Identifier N = Nickel Barrier, 6 = EIA "J" Code B = Bulk Tinned Termination "Leave blank if D = Paper Tape ( 10" Reel ) Composition is No Marking" E = Embossed Tape ( 7" Reel ) 100% matte Tin (Sn) P = Paper Tape ( 7" Reel ) P = Palladium Silver R = Paper Tape ( 13" Reel ) G = Gold over Nickel U = Embossed Tape ( 13" Reel ) P: For Palladium Silver Termination (PdAg) add P above. ** 0201 and 0402 Pb: For 90% Tin (Sn)/10% Lead (Pb) Termination size capacitors add Pb above. cannot be Standard termination finish for this product is marked 100% matte Tin (Sn) only.
P
--
*
- * OPTIONAL IDENTIFIER Min./ Max. thickness
- designates minimum thickness * designates maximum thickness
CODE: DIMENSION:
The following letters define thickness as signified below: B C D E F G H I J K L M N O P Q R 6 9 .010 .015 .020 .026 .030 .035 .040 .045 .050 .055 .060 .065 .070 .075 .080 .085 .090 .023 .021
Please Note: Venkel offers Engineering Kits for this product. See page 121 for details.
7
www..com
Ceramic Chip Capacitors
NP0/C0G Dielectric
L W T
END BAND
Values that are typically available. 25V Available in 25V only.
(All measurements in inches)
Size
01005 ( 0.0008) .016 .008 .008 .002 16V 0.5pF
0201 ( 0.002) .024 .012 .012 .002 25V
0402 ( 0.004) .040 .020 .025 .004 25V 50V
0504 ( 0.008) .050 .040 .040 .005 50V 100V
0603 ( 0.006) .063 .032 .033 .008 50V 100V 25V
0805 ( 0.008) .080 .050 .055 .020 .010 50V 100V
1206 ( 0.008) .126 .063 .070 .020 .010 50V 100V
1210 (0.008) .126 .098 .075 .020 .010 50V 100V
1812 (0.012) .177 .126 .085 .024 .015 50V 100V
L W T (max) Min E/B
VDCW (MAX)
<-----------------------------------------------------------------------------------------------CAP. CODE-----------------------------------------------------------------------------------------------> <-----------------------------------------------------------------------------------------------CAP. VALUE---------------------------------------------------------------------------------------------->
0R5 1R0 1R2 1R5 1R8 2R2 2R7 3R3 3R9 4R7 5R6 6R8 8R2 100 120 150 180 220 270 330 390 470 560 680 820 101 121 151 181 221 271 331 391 471 561 681 821 102 122 152 182 222 272 332
1.2 1.5
2.0
2.2 2.7 3.3
3.0
9.0 8.0 7.0 6.0 5.0 4.0
4.7 5.6 6.8 8.2 10pF 12 15 18 22 27 33 39 47 56 68 82 100pF 120 150 180 220 270 330 390 470 560 680 820 1000pF 1200 1500 1800 2200 2700 3300
Note: Due to demand and raw material fluctuations in the market, changes and availability of individual values may occur. Minimum order quantities may apply.
8
9.0 8.0 7.0 6.0 5.0 4.0
3.9
3.0
2.0
1.8
Va l u e s s h o w n t o t h e l e f t a re a l s o a v a i l a b l e f o r 0 2 0 1 s i z e o n l y
Va l u e s s h o w n t o t h e l e f t a re a v a i l a b l e f o r 0 1 0 0 5 s i z e o n l y
1.0pF
www..com
Ceramic Chip Capacitors
NP0/C0G Dielectric
L W T
END BAND
Values that are typically available. 25V Available in 25V only.
(All measurements in inches)
Size
0201 ( 0.002) .024 .012 .012 .002 25V 3900 4700 5600 6800 8200 .01F .012 .015 .018 .022 .027 .033 .039 .047 .056 .068 .082 .100F .120 .150 .180 .220 .270 .330 .390 .470 .560 .680 .820 1.00F 1.20 1.50 1.80 2.20 3.30 3.90 4.70 6.80 10.0F 15.0F 22.0F 47.0F 100.0F Note:
0402 ( 0.004) .040 .020 .025 .004 25V 50V
0504 ( 0.008) .050 .040 .040 .005 50V 100V
0603 ( 0.006) .063 .032 .033 .008 50V 100V 25V
0805 ( 0.008) .080 .050 .055 .020 .010 50V 100V
1206 ( 0.008) .126 .063 .070 .020 .010 50V 100V
1210 (0.008) .126 .098 .075 .020 .010 50V 100V
1812 (0.012) .177 .126 .085 .024 .015 50V 100V
2220 / 2221 (0.016) .225 / .225 .200 / .210 .108 /.108 .025 .015 50V 100V
L W T (max) Min E/B
VDCW (MAX) <--------------------------------------------------------------------------------------------CAP. CODE--------------------------------------------------------------------------------------------> <--------------------------------------------------------------------------------------------CAP. VALUE-------------------------------------------------------------------------------------------> 392 472 562 682 822 103 123 153 183 223 273 333 393 473 563 683 823 104 124 154 184 224 274 334 394 474 564 684 824 105 125 155 185 225 335 395 475 685 106 156 226 476 107
25V
*
Due to demand and raw material fluctuations in the market, changes and availability of individual values may occur. Minimum order quantities may apply.
9
www..com
Ceramic Chip Capacitors
X7R Dielectric
L W T
END BAND
Values that are typically available. X5R Available in X5R only. See X5R chart on page 12, for all values 1F and above
(All measurements in inches)
Size
0201 ( 0.002) .024 .012 .012 .002 6.3V 100pF 120 150 180 220 270 330 390 470 560 680 820 1000pF 1200 1500 1800 2200 2700 3300 3900 4700 5600 6800 8200 .01F .012 .015 .018 .022 .027 .033 X5R X5R X5R 10V 16V 16V
0402 ( 0.004) .040 .020 .025 .004 25V 50V 25V
0504 ( 0.008) .050 .040 .040 .005 50V 100V 6.3V 10V
0603 ( 0.006) .063 .032 .033 .008 16V 25V 50V 100V 10V 16V
0805 ( 0.008) .080 .050 .055 .020 .010 25V 50V 100V
L W T (max)* Min E/B
VDCW (MAX) <----------------------------------------------------------------------------------------------CAP. CODE----------------------------------------------------------------------------------------------> <----------------------------------------------------------------------------------------------CAP. VALUE---------------------------------------------------------------------------------------------> 101 121 151 181 221 271 331 391 471 561 681 821 102 122 152 182 222 272 332 392 472 562 682 822 103 123 153 183 223 273 333
* For values above 1uF, thickness may be greater than specified above. T(max): 0603 - 0.048" 0805 - 0.075" Note: Due to demand and raw material fluctuations in the market, changes and availability of individual values may occur. Minimum order quantities may apply.
10
www..com
Ceramic Chip Capacitors
X7R Dielectric
L W T
END BAND
Values that are typically available. X5R Available in X5R only. See X5R chart on page 12, for all values 1F and above
(All measurements in inches)
Size
0201 ( 0.002) .024 .012 .012 .002 6.3V .039 .047 .056 .068 .082 .100F .120 .150 .180 .220 .270 .330 .390 .470 .560 .680 .820 1.00F 1.20 1.50 1.80 2.20 3.30 4.70 6.80 10.0F 15.0F 22.0F 47.0F 100.0F X5R X5R X5R X5R X5R X5R X5R 10V 16V 6.3V
0402 ( 0.004) .040 .020 .025 .004 10V 16V 25V
0504 ( 0.008) .050 .040 .040 .005 50V 100V 6.3V 10V
0603 ( 0.006) .063 .032 .033 .008 16V 25V 50V 100V 10V 16V
0805 ( 0.008) .080 .050 .055 .020 .010 25V 50V 100V
L W T (max)* Min E/B
VDCW (MAX) 393 473 563 683 823 104 124 154 184 224 274 334 394 474 564 684 824 105 125 155 185 225 335 475 685 106 156 226 476 107 <----------------------------------------------------------------------------------------------CAP. VALUE------------------------------------------------------------------------------------------> <----------------------------------------------------------------------------------------------CAP. CODE------------------------------------------------------------------------------------------>
X5R
X5R
X5R
* For values above 1uF, thickness may be greater than specified above. T(max): 0603 - 0.048" 0805 - 0.075" Note: Due to demand and raw material fluctuations in the market, changes and availability of individual values may occur. Minimum order quantities may apply.
11
www..com
Ceramic Chip Capacitors
X7R Dielectric
L W T
END BAND
Values that are typically available. X5R Available in X5R only. See X5R chart on page 12, for all values 1F and above
(All measurements in inches)
Size
1206 ( 0.008) .126 .063 .070 .020 .010 10V 1000pF 1200 1500 1800 2200 2700 3300 3900 4700 5600 6800 8200 .01F .012 .015 .018 .022 .027 .033 .039 .047 .056 .068 .082 .100F .120 .150 .180 .220 .270 .330 16V 25V 50V 100V 10V 16V
1210 (0.008) .126 .098 .075 .020 .010 25V 50V 100V 6.3V 10V
1812 (0.012) .177 .126 .085 .024 .015 16V 25V 50V 100V 16V
2220 / 2221 (0.016) .225 / .225 .200 / .210 .108 /.108 .025 .015 25V 50V 100V
L W T (max)* Min E/B
VDCW (MAX) <----------------------------------------------------------------------------------------------CAP. CODE----------------------------------------------------------------------------------------------> <----------------------------------------------------------------------------------------------CAP. VALUE---------------------------------------------------------------------------------------------> 102 122 152 182 222 272 332 392 472 562 682 822 103 123 153 183 223 273 333 393 473 563 683 823 104 124 154 184 224 274 334
* For values above 1uF, thickness may be greater than specified above. T(max): 1206 - 0.110" 1812 - 0.130" 1210 - 0.125" 2220 - 0.135" Note: Due to demand and raw material fluctuations in the market, changes and availability of individual values may occur. Minimum order quantities may apply.
12
www..com
Ceramic Chip Capacitors
X7R Dielectric
L W T
END BAND
Values that are typically available. X5R Available in X5R only. See X5R chart on page 12, for all values 1F and above
(All measurements in inches)
Size
1206 ( 0.008) .126 .063 .070 .020 .010 10V .390 .470 .560 .680 .820 1.00F 1.20 1.50 1.80 2.20 3.30 4.70 6.80 10.0F 15.0F 22.0F 47.0F 100.0F 16V 25V 50V 100V 10V 16V
1210 (0.008) .126 .098 .075 .020 .010 25V 50V 100V 6.3V 10V
1812 (0.012) .177 .126 .085 .024 .015 16V 25V 50V 100V 16V
2220 / 2221 (0.016) .225 / .225 .200 / .210 .108 /.108 .025 .015 25V 50V 100V
L W T (max)* Min E/B
VDCW (MAX) 394 474 564 684 824 105 125 155 185 225 335 475 685 106 156 226 476 107 <-----------------------------------------------------CAP. VALUE--------------------------------------------------> <-----------------------------------------------------CAP. CODE-------------------------------------------------->
X5R
X5R X5R X5R
X5R
* For values above 1uF, thickness may be greater than specified above. T(max): 1206 - 0.110" 1812 - 0.130" 1210 - 0.125" 2220 - 0.135" Note: Due to demand and raw material fluctuations in the market, changes and availability of individual values may occur. Minimum order quantities may apply.
13
www..com
Ceramic Chip Capacitors
X5R Dielectric (Minimum 1F)
L W T
END BAND
Values that are typically available.
(All measurements in inches)
Size
0402 ( 0.004) .040 .020 .025 .004 6.3V 1.00F 1.20 1.50 1.80 2.20 3.30 4V 6.3V
0603 ( 0.006) .063 .032 .033 .008 10V 16V 25V 6.3V
0805 ( 0.008) .080 .050 .055 .020 .010 10V 16V 25V 6.3V
1206 ( 0.008) .126 .063 .070 .020 .010 10V 16V 25V 6.3V
1210 (0.008) .126 .098 .075 .020 .010 10V 16V 25V 6.3V
1812 (0.012) .177 .126 .085 .024 .015 10V 16V 25V 6.3V
2220 / 2221 (0.016) .225 / .225 .200 / .210 .108 /.108 .025 .015 10V 25V
L W T (max) Min E/B
VDCW (MAX) 105 125 155 185 225 335 <------------CAP. VALUE-----------> <------------CAP. CODE----------->
* For values above 1uF, thickness may be greater than specified above. T(max): 1206 - 0.110" 1812 - 0.130" 1210 - 0.125" 2220 - 0.135" Note: Due to demand and raw material fluctuations in the market, changes and availability of individual values may occur. Minimum order quantities may apply.
14
www..com
Ceramic Chip Capacitors
X5R Dielectric (Minimum 1F)
L W T
END BAND
Values that are typically available.
(All measurements in inches)
Size
0402 ( 0.004) .040 .020 .025 .004 6.3V 3.90 4.70 6.80 10.0F 15.0F 22.0F 47.0F 100.0F 4V 6.3V
0603 ( 0.006) .063 .032 .033 .008 10V 16V 25V 6.3V
0805 ( 0.008) .080 .050 .055 .020 .010 10V 16V 25V 6.3V
1206 ( 0.008) .126 .063 .070 .020 .010 10V 16V 25V 6.3V
1210 (0.008) .126 .098 .075 .020 .010 10V 16V 25V 6.3V
1812 (0.012) .177 .126 .085 .024 .015 10V 16V 25V 6.3V
2220 / 2221 (0.016) .225 / .225 .200 / .210 .108 /.108 .025 .015 10V 25V
L W T (max) Min E/B
VDCW (MAX) 395 475 685 106 156 226 476 107 <-----------------CAP. VALUE-----------------> <-----------------CAP. CODE----------------->
* For values above 1uF, thickness may be greater than specified above. T(max): 1206 - 0.110" 1812 - 0.130" 1210 - 0.125" 2220 - 0.135" Note: Due to demand and raw material fluctuations in the market, changes and availability of individual values may occur. Minimum order quantities may apply.
15
www..com
Ceramic Chip Capacitors
Z5U Dielectric
L W T
END BAND
Values that are typically available.
(All measurements in inches)
Size
0504 ( 0.008) .050 .040 .040 .005 25V 1000pF 1200 1500 1800 2200 2700 3300 3900 4700 5600 6800 8200 .01F .012 .015 .018 .022 .027 .033 .039 .047 .056 .068 .082 .100F .120 .150 .180 .220 .270 .330 Note: 50V
0603 ( 0.006) .063 .032 .033 .008 25V 50V
0805 ( 0.008) .080 .050 .055 .020 .010 25V 50V
1206 ( 0.008) .126 .063 .070 .020 .010 25V 50V
1210 (0.008) .126 .098 .075 .020 .010 25V 50V
1812 (0.012) .177 .126 .085 .024 .015 25V 50V
2220 / 2221 (0.016) .225 / .225 .200 / .210 .108 /.108 .025 .015 25V 50V
L W T (max) Min E/B
VDCW (MAX) <----------------------------------------------------------------------------------------------CAP. CODE----------------------------------------------------------------------------------------------> <----------------------------------------------------------------------------------------------CAP. VALUE---------------------------------------------------------------------------------------------> 102 122 152 182 222 272 332 392 472 562 682 822 103 123 153 183 223 273 333 393 473 563 683 823 104 124 154 184 224 274 334
Due to demand and raw material fluctuations in the market, changes and availability of individual values may occur. Minimum order quantities may apply.
16
www..com
Ceramic Chip Capacitors
Z5U Dielectric
L W T
END BAND
Values that are typically available.
(All measurements in inches)
Size
0504 ( 0.008) .050 .040 .040 .005 25V .390 .470 .560 .680 .820 1.00F 1.20 1.50 1.80 2.20 3.30 3.90 4.70 6.80 10.0F 15.0F 22.0F 47.0F 100.0F Note: 50V
0603 ( 0.006) .063 .032 .033 .008 25V 50V
0805 ( 0.008) .080 .050 .055 .020 .010 25V 50V
1206 ( 0.008) .126 .063 .070 .020 .010 25V 50V
1210 (0.008) .126 .098 .075 .020 .010 25V 50V
1812 (0.012) .177 .126 .085 .024 .015 25V 50V
2220 / 2221 (0.016) .225 / .225 .200 / .210 .108 /.108 .025 .015 25V 50V
L W T (max) Min E/B
VDCW (MAX) <-------------------------------------------------------CAP. VALUE-----------------------------------------------------> <-------------------------------------------------------CAP. CODE-----------------------------------------------------> 394 474 564 684 824 105 125 155 185 225 335 395 475 685 106 156 226 476 107
Due to demand and raw material fluctuations in the market, changes and availability of individual values may occur. Minimum order quantities may apply.
17
www..com
Ceramic Chip Capacitors
Y5V Dielectric
L W T
END BAND
Values that are typically available.
(All measurements in inches)
Size
0201 ( 0.002) .024 .012 .012 .002 10V 1000pF 1200 1500 1800 2200 2700 3300 3900 4700 5600 6800 8200 .01F .012 .015 .018 .022 .027 .033 .039 .047 .056 .068 .082 .100F .120 .150 .180 .220 .270 .330 Note: 6.3V
0402 ( 0.004) .040 .020 .025 .004 10V 16V 25V 50V 6.3V
0603 ( 0.006) .063 .032 .033 .008 10V 16V 25V 50V 6.3V
0805 ( 0.008) .080 .050 .055 .020 .010 10V 16V 25V 50V 10V
1206 ( 0.008) .126 .063 .070 .020 .010 16V 25V 50V 6.3V
1210 (0.008) .126 .098 .075 .020 .010 10V 16V 25V
1812 (0.012) .177 .126 .085 .024 .015 6.3V 10V 25V
L W T (max) Min E/B
VDCW (MAX) <----------------------------------------------------------------------------------------------CAP. CODE---------------------------------------------------------------------------------------------> 102 122 152 182 222 272 332 392 472 562 682 822 103 123 153 183 223 273 333 393 473 563 683 823 104 124 154 184 224 274 334 <----------------------------------------------------------------------------------------------CAP. VALUE--------------------------------------------------------------------------------------------->
Due to demand and raw material fluctuations in the market, changes and availability of individual values may occur. Minimum order quantities may apply.
18
www..com
Ceramic Chip Capacitors
Y5V Dielectric
L W T
END BAND
Values that are typically available.
(All measurements in inches)
Size
0201 ( 0.002) .024 .012 .012 .002 10V .390 .470 .560 .680 .820 1.00F 1.20 1.50 1.80 2.20 3.30 3.90 4.70 6.80 10.0F 15.0F 22.0F 47.0F 100.0F 6.3V
0402 ( 0.004) .040 .020 .025 .004 10V 16V 25V 50V 6.3V
0603 ( 0.006) .063 .032 .033 .008 10V 16V 25V 50V 6.3V
0805 ( 0.008) .080 .050 .055 .020 .010 10V 16V 25V 50V 10V
1206 ( 0.008) .126 .063 .070 .020 .010 16V 25V 50V 6.3V
1210 (0.008) .126 .098 .075 .020 .010 10V 16V 25V
1812 (0.012) .177 .126 .085 .024 .015 6.3V 10V 25V
L W T (max) Min E/B
VDCW (MAX) 394 474 564 684 824 105 125 155 185 225 335 395 475 685 106 156 226 476 107 <------------------------------------------------------CAP. VALUE------------------------------------------------------> <------------------------------------------------------CAP. CODE------------------------------------------------------>
Note: Due to demand and raw material fluctuations in the market, changes and availability of individual values may occur. Minimum order quantities may apply.
All components in this section are RoHS compliant per the EU directives and definitions.
19

▲Up To Search▲

Price & Availability of C0805X7R160-XXXX

	To Download C0805X7R160-XXXX Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .